The excavator has a wide operating range and relatively high use frequency. After a long time of operation, there will be varying degrees of wear and failure. Today, taking the long arm excavator as an example, let's talk about what we should do when facing problems in operation.

故障1:斗杆油缸的膨胀和收缩缓慢而微弱

Fault 1: The stick cylinder expands and contracts slowly and weakly

在长臂挖掘机工作过程中，如果斗杆油缸膨胀缓慢且薄弱，我们应进行如下检查。

During the operation of long arm excavator, if the stick cylinder expands slowly and is weak, we should carry out the following inspections.

1.检查密封是否失效。松开低压腔的油管，释放腔内的液压油，然后启动发动机向高压腔内注入压力油。没有液压油流出低压室的油管，表明斗杆油缸的活塞密封良好。如果密封失效，低压腔和高压腔中的液压油将由于内部泄漏而相互交叉。

1. Check whether the seal is invalid. First, loosen the oil pipe in the low-pressure chamber, release the hydraulic oil in the chamber, and then start the engine to inject pressure oil into the high-pressure chamber. No hydraulic oil flows out of the oil pipe in the low pressure chamber, indicating that the piston of the stick cylinder is well sealed. If the seal fails, the hydraulic oil in the low-pressure chamber and high-pressure chamber will cross each other due to internal leakage.

2.检查PPC阀和主控制阀。PPC阀，又称先导式控制阀，是一种比例压力控制阀，它可以根据操作手柄的行程输出相应的控制压力和流量，使主控阀芯有相应的运动，从而起到控制执行器速度的作用。主控制阀中的每个阀芯控制油路的开关。如果一个阀芯磨损、卡住或甚堵塞，相应致动器的油压和流量将降低，导致致动器动作缓慢甚不动作。

2. Check PPC valve and main control valve. PPC valve, also known as pilot control valve, is a proportional pressure control valve. It can output corresponding control pressure and flow according to the stroke of the operating handle, so that the main control valve core can move accordingly, thus controlling the speed of the actuator. Each spool in the main control valve controls the switch of the oil circuit. If a valve element is worn, stuck or even blocked, the oil pressure and flow of the corresponding actuator will decrease, resulting in slow or even no action of the actuator.

如果斗杆油缸回路的控制油管更换为工作正常的压力控制阀，故障将消失。

If the control oil line for the stick cylinder circuit is replaced with a pressure control valve that is working properly, the problem will disappear.

故障2:行走偏差

Fault 2: Travel deviation

当长臂挖掘机出现跑偏故障时，应检查挖掘机组合阀。拆下限压阀上的两根油管，用塞子堵住出油口，启动发动机，用塞子组合阀和长臂挖掘机拉动行走控制手柄，检查油压是否正常；拆卸行走组合阀另一侧的两根油管，再次启动发动机，观察其限压阀的两个油孔是否有油流出。如果没有这种现象，排除组合阀的故障。

In case of deviation fault of long arm excavator, check the excavator combination valve first. Remove the two oil pipes on the lower pressure valve, block the oil outlet with plugs, start the engine, pull the travel control handle with the plug combination valve and the long arm excavator, and check whether the oil pressure is normal; Remove the two oil pipes on the other side of the travel combination valve, start the engine again, and observe whether there is oil flowing out of the two oil holes of the pressure limiting valve. If there is no such phenomenon, troubleshoot the combination valve.

由于旋转接头处有许多油道，容易相互串通，我们可以先拆卸行走电机的两根油管，然后连接行走电机的一根油管。该动作完成后，再次起动发动机，拉动堵塞油管马达的换向阀，观察油压是否过低，液压的油孔是否有油流出。如果有，则认为是旋转接头的油道密封问题，更换后才能。

Since there are many oil channels at the rotary joint, which are easy to connect with each other, we can remove two oil pipes of the traveling motor first, and then connect one oil pipe of the traveling motor. After this action is completed, start the engine again, pull the reversing valve of the motor that blocks the oil pipe, and observe whether the oil pressure is too low and whether there is oil flowing out of the hydraulic oil hole. If yes, it is considered that the problem is caused by the sealing of the oil passage of the rotary joint, which can be solved only after replacement.

故障3:惯性旋转角度太大

Fault 3: Inertial rotation angle is too large

在增华体会国际 的过程中，由于转弯制动不及时或制动力不足，在惯性力的作用下，上部机体的转弯角度过大。鉴于这个故障问题，我们应该按如下方式处理:

In the process of adding long arm excavator, the turning angle of upper body is too large under the action of inertial force due to untimely turning brake or insufficient braking force. In view of this problem, we should handle it as follows:

1.检查旋转锁紧阀的电路连接是否牢固，有无短路或断路，并测量电磁阀线圈和阀芯工作是否正常；

1. Check whether the circuit connection of the rotary lock valve is firm, whether there is short circuit or open circuit, and measure whether the solenoid valve coil and valve core work normally;

2.测量并检查制动油压是否在正常范围内(正常范围油压为3 MpA)；

2. Measure and check whether the brake oil pressure is within the normal range (the oil pressure within the normal range is 3 Mpa);

3.拆下旋转电机，检查弹簧是否断裂，弹性是否正常，制动压盘上的密封圈是否完好。

3. Dismantle the rotating motor, check whether the spring is broken, whether the elasticity is normal, and whether the sealing ring on the brake pressure plate is intact.

以上就是为大家介绍的有关 华体会国际 租赁的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务 //www.wondgo.com

The above is a detailed introduction to the leasing of the extended boom excavator, and we hope it will be helpful to you. If you have any questions, please contact us. We will provide services for you with our attitude //www.wondgo.com