1.检查密封是否失效。松开低压腔的油管，释放腔内的液压油，然后启动发动机向高压腔内注入压力油。没有液压油流出低压室的油管，表明斗杆油缸的活塞密封良好。如果密封失效，低压腔和高压腔中的液压油将由于内部泄漏而相互交叉。
1. Check whether the seal fails. First loosen the oil pipe in the low-pressure chamber to release the hydraulic oil in the chamber, and then start the engine to inject pressure oil into the high-pressure chamber. No hydraulic oil flows out of the oil pipe of the low-pressure chamber, indicating that the piston of the stick cylinder is well sealed. If the seal fails, the hydraulic oil in the low-pressure chamber and the high-pressure chamber will cross each other due to internal leakage.
2.检查PPC阀和主控制阀。PPC阀，又称先导式控制阀，是一种比例压力控制阀，它可以根据操作手柄的行程输出相应的控制压力和流量，使主控阀芯有相应的运动，从而起到控制执行器速度的作用。主控制阀中的每个阀芯控制油路的开关。如果一个阀芯磨损、卡住或甚堵塞，相应致动器的油压和流量将降低，导致致动器动作缓慢甚不动作。
2. Check PPC valve and main control valve. PPC valve, also known as pilot control valve, is a proportional pressure control valve. It can output the corresponding control pressure and flow according to the stroke of the operating handle to make the main control valve core move accordingly, so as to control the speed of the actuator. Each spool in the main control valve controls the switch of the oil circuit. If a valve core is worn, stuck or even blocked, the oil pressure and flow of the corresponding actuator will be reduced, resulting in slow or even no action of the actuator.
如果斗杆油缸回路的控制油管更换为工作正常的压力控制阀，故障将消失。
If the control oil pipe of the stick cylinder circuit is replaced with a pressure control valve that works normally, the fault will disappear.
故障2:行走偏差
Fault 2: Travel Deviation
当长臂挖掘机出现跑偏故障时，应检查挖掘机组合阀。拆下限压阀上的两根油管，用塞子堵住出油口，启动发动机，用塞子组合阀和长臂挖掘机拉动行走控制手柄，检查油压是否正常；拆卸行走组合阀另一侧的两根油管，再次启动发动机，观察其限压阀的两个油孔是否有油流出。如果没有这种现象，排除组合阀的故障。

When the long arm excavator has deviation fault, first check the excavator combination valve. Remove the two oil pipes on the lower pressure valve, block the oil outlet with a plug, start the engine, pull the travel control handle with a plug combination valve and a long arm excavator, and check whether the oil pressure is normal; Remove the two oil pipes on the other side of the travel combination valve, start the engine again, and observe whether there is oil flowing out of the two oil holes of the pressure limiting valve. If there is no such phenomenon, troubleshoot the combination valve.
此时，我们应该检查中间的旋转接头。
At this point, we should check the swivel joint in the middle.
由于旋转接头处有许多油道，容易相互串通，我们可以先拆卸行走电机的两根油管，然后连接行走电机的一根油管。该动作完成后，再次起动发动机，拉动堵塞油管马达的换向阀，观察油压是否过低，液压处的马达的油孔是否有油流出。如果有，则认为是旋转接头的油道密封问题，更换后才能。
Because there are many oil passages at the rotary joint, it is easy to collude with each other. We can first disassemble the two oil pipes of the walking motor, and then connect one oil pipe of the walking motor. After this action is completed, start the engine again, pull the change-over valve blocking the oil pipe motor, and observe whether the oil pressure is too low and whether there is oil flowing out of the oil hole of the motor at the hydraulic pressure. If yes, it is considered to be the oil passage sealing problem of the rotary joint, which can be solved only after replacement.
故障3:惯性旋转角度太大
Fault 3: inertia rotation angle is too large
在增华体会国际 的过程中，由于转弯制动不及时或制动力不足，在惯性力的作用下，上部机体的转弯角度过大。鉴于这个故障问题，我们应该按如下方式处理:
In the process of adding long arm excavator, the turning angle of the upper body is too large under the action of inertial force due to untimely turning braking or insufficient braking force. In view of this fault problem, we should deal with it as follows:
1.检查旋转锁紧阀的电路连接是否牢固，有无短路或断路，并测量电磁阀线圈和阀芯工作是否正常；
1. Check whether the circuit connection of the rotary locking valve is firm, whether there is short circuit or open circuit, and measure whether the solenoid valve coil and valve core work normally;
2.测量并检查制动油压是否在正常范围内(正常范围油压为3 MpA)；
2. Measure and check whether the brake oil pressure is within the normal range (the oil pressure in the normal range is 3 MPa);
3.拆下旋转电机，检查弹簧是否断裂，弹性是否正常，制动压盘上的密封圈是否完好。
3. Remove the rotating motor and check whether the spring is broken, whether the elasticity is normal and whether the sealing ring on the brake pressure plate is intact.
以上内容就是今天小编为您介绍的长臂挖掘机//www.wondgo.com的相关知识，更多的内容请继续关注我们。
The above content is the long arm excavator introduced to you by Xiaobian today //www.wondgo.com For more information, please continue to pay attention to us.